EIGRP Routing Commands for Router A
RouterA#show ip route
Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP
i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area
* – candidate default, U – per-user static route, o – ODR
P – periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, FastEthernet0/0
C 20.0.0.0/8 is directly connected, Serial0/0
RouterA#config t
Enter configuration commands, one per line. End with CNTL/Z.
RouterA(config)#router eigrp 111
RouterA(config-router)#network 10.0.0.0
RouterA(config-router)#network 20.0.0.0
RouterA(config-router)#
—————-after configure Router B———————-
%DUAL-5-NBRCHANGE: IP-EIGRP 111: Neighbor 20.0.0.2 (Serial0/0) is up: new adjacency
RouterA#show ip route
Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP
i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area
* – candidate default, U – per-user static route, o – ODR
P – periodic downloaded static route
Gateway of last resort is not set
C 10.0.0.0/8 is directly connected, FastEthernet0/0
C 20.0.0.0/8 is directly connected, Serial0/0
D 30.0.0.0/8 [90/2172416] via 20.0.0.2, 00:00:38, Serial0/0
RouterA#ping 30.0.0.1
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 30.0.0.1, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 31/31/32 ms
RouterA#
EIGRP Routing Commands for Router B
RouterB>enable
RouterB#show ip route
Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP
i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area
* – candidate default, U – per-user static route, o – ODR
P – periodic downloaded static route
Gateway of last resort is not set
C 20.0.0.0/8 is directly connected, Serial0/0
C 30.0.0.0/8 is directly connected, FastEthernet0/0
RouterB#conf t
Enter configuration commands, one per line. End with CNTL/Z.
RouterB(config)#router eigrp 111
RouterB(config-router)#network 20.0.0.0
RouterB(config-router)#
%DUAL-5-NBRCHANGE: IP-EIGRP 111: Neighbor 20.0.0.1 (Serial0/0) is up: new adjacency
RouterB(config-router)#network 30.0.0.0
RouterB(config-router)#exit
RouterB(config)#exit
%SYS-5-CONFIG_I: Configured from console by console
RouterB#show ip route
Codes: C – connected, S – static, I – IGRP, R – RIP, M – mobile, B – BGP
D – EIGRP, EX – EIGRP external, O – OSPF, IA – OSPF inter area
N1 – OSPF NSSA external type 1, N2 – OSPF NSSA external type 2
E1 – OSPF external type 1, E2 – OSPF external type 2, E – EGP
i – IS-IS, L1 – IS-IS level-1, L2 – IS-IS level-2, ia – IS-IS inter area
* – candidate default, U – per-user static route, o – ODR
P – periodic downloaded static route
Gateway of last resort is not set
D 10.0.0.0/8 [90/2172416] via 20.0.0.1, 00:00:20, Serial0/0
C 20.0.0.0/8 is directly connected, Serial0/0
C 30.0.0.0/8 is directly connected, FastEthernet0/0
RouterB#ping 10.0.0.10
Type escape sequence to abort.
Sending 5, 100-byte ICMP Echos to 10.0.0.10, timeout is 2 seconds:
!!!!!
Success rate is 100 percent (5/5), round-trip min/avg/max = 62/62/63 ms
RouterB#
No comments:
Post a Comment